Etusivu
Kirjaudu sisään
Datadivarin kotikirppis
Elektroniikka
Radiopuhelimet
Romutettavat radiot varaosina
Kaapelit
Liitin
ATK-Osia
Rompetori
Tarjoukset
Vintage
Valmistajat
Valitse
ACP
AMD
Apple
Asus
Atmel
Baofeng
Canon
Compaq
Dallas
Datadivari
Dell
Epcos
Evox
Fairchild
Fujitsu
Hewlett Packard
Hitachi
Intel
IRF
ITT
Kemet
Kenwood
König
Mascot
Matrox
MAXIM
MAXWELL
Mersedes Benz
Microchip
Microsoft
Mitsubishi
Motorola
Murata
National
NCC
NEC
Nic
Nichicon
Nokia
NXP
Omron
Pace
Panasonic
Philips
Plessey
RCA
Rohde & Schwarz
Rohm
RUF Electronic
Samsung
Sanken
SANYO
Semtech
Sharp
Siemens
Sony
ST
Tetronix
Texas Instrumen..
Toshiba
Uniden
Vertex
Vishay
Yaesu
Zilog
Mitä mieltä tuotteista?...
Kerro meille mitä mieltä olet tästä tuotteesta.
Tietoja
Toimitusehdot
Yksityisyyssuoja
Käyttöehdot
Yhteystiedot
Tietoja Lahjakortiteista
Peru uutiskirjeen tilaus
Valuutat
US Dollar
Euro
GB Pound
Rupla
Jeni
Randi
Etusivu
Elektroniikka
Radiot
Diy kit ,Air band receiver,High sensitivity aviation radio
Diy kit ,Air band receiver,High sensitivity aviation radio
suurempi kuva
suurempi kuva
suurempi kuva
suurempi kuva
suurempi kuva
Paino: 0.25kg
1 Kpl varastossa
35.00€
Lisää koriin:
Uusi A1. Koottu ja koteloitu, testattu ja toimiva laite. Alignment & Adjustment:
Aligning the Aviation receiver consists of nothing more than adjusting the slug in the local-oscillator coil (L6) for the center of the desired tuning range, and peaking the IF transformer (T1). The receiver can be calibrated using a VHF RF signal generator, frequency counter, or another VHF receiver by setting R1 to its mid-position; remember that you want to set the local-oscillator frequency 10.7-MHz higher than the desired signal or range to be received.
Then, using a non-metallic alignment tool--a metal tool of any kind will drastically detune the coil, making alignment almost impossible--adjust the Local Oscillator coil L6 until you hear aircraft or aircraft communications. If you find that you're receiving a lot of FM broadcase stations, then you have adjusted the slug too far down into the coil. Turn it back until it is a bit higher than the coil form and try again. Once you're receiving aircraft or airport frequencies, adjust T1 for the best reception. Typically, T1 is adjusted 2-3 turns from the top of the shield can. If you don't have any signal-reference equipment or alignment, and are not yet hearing airplanes, your best bet is to pack-up the receiver and the necessary alignment tools, and head for the nearest airport! If the airport has no control tower, visit a general aviation center on the airport grounds, and ask which are the most active frequencies. Then adjust L6 and R1 until you hear the action. It should be obvious that alignment will test your patience if you do not live near a large airport.
Stretching L1, L3, and L5 at the antenna input will provide greater sensitivity if you have problems receiving a signal. Also, as mentioned before, ensure that L1, L3, and L5 are mounted a *little* bit above the pcb.
A ground-service operator or private pilot may be willing to give you a brief test transmission on the 122.8 Unicom frequency. And if your airport has ATIS transmissions you can get a steady test signal as soon as you are within line-of-sight of its antenna. (See the explanation of Unicom and ATIS down the bottom of this document). It is best to align the receiver right there at your local airport.
Tuote 7/12
Edellinen
Palaa tuotelistaan
Seuraava
Kirjoita arvostelu
Tämä tuote on tullut valikoimiimme perjantai 23 tammikuu, 2015.
Sponsorit
Tavaroiden kuntoluokitus: A1 Uusi, A2 Uudenveroinen B1 Erittäin hyvä, B2 Täysin kunnossa C1 Korjauskelpoinen, C2 Varaosiksi
Oletko nähnyt ...
Ohjelmapäivityksiä tehty ja osa skandimerkeistä sekoilee toistaiseksi.
Ostoskori...
on tyhjä
Etusivu
IP osoitteesi: 3.239.236.140
Copyright © 2021
Datadivari
. Powered by
Zen Cart